< img style = "margin: 0px; padding: 0px; border: 0px; vertical-align: top;" Title = "Installation of ACM Unititan/Titan Central Motor" SRC = "https://www.e-toolshop.gr/wp-content/uploads/2020/12/mechanical_installation-001.gif" ALT = "Installation of ACM Unititan Motor Motor /Titan ”/>
- we open a hunt Φ10, at the top of the shaft and at a distance of 5 cm from the center of the axis.
- remove screws M10 by the drum of the motor.
- remove the two half (up & amp; below) of the drum of the motor, unscrewing the two m8 screws (using a 6 mm key).
- carefully remove the Black plastic stripe that is the roller of the drum of the motor. The strip is covered with grease so we must be careful not to stick trash. We do not remove the grease.
- remove the two Half (Top & Amp; Lower) of the trunk of the motor, unscrewing the four M8 screws (using Allen Key 6 mm).
- if required, We place the white plastic adapter of the shaft diameter by placing it based on the Φ10 hole we have already opened.
- join the two two Half (Top & Amp; Lower) of the trunk of the motor, screwing the four M8 screws (using 6 mm Allen key) to hug the roll of the roll.
- we screw in one screw M10 (the one with the hexagonal head with no nuts) in the hole Φ10 (using 17 mm French wrench) in a way that passes through its interior.
- carefully place in the Its position the black plastic stripe that is the drum roller.
- join the two two half (up & amp; below) of the drum of the motor, screwing two m8 screws (using Allen 6 mm).
- we screw the other screw M10 (the one with the hexagonal head with a nut)
- if required, We place the black plastic adapter in diameter of the drums, by buttoning it at the top of the motor drum.
-
- connect the above part of the roll curtain with the motor drum. To this end we screw the corresponding M10 screw, along with its washer, into the thread of the top half of the motor drum (using 17 mm French wrench).
- we open two holes On the axis: one for the motor cable and one for the disintegration cable. We make sure that holes do not have sharp lips that may injure the cable or cable.
- pass through First hole inside the axis the 4 × 1.0 mm² cable accompanying the motor (make sure the cable stays away from the moving parts of the roll). The cable comes out of the edge of the shaft, to the side of the roll. We connect the cable (in the 3 contacts of the Clema and the trunk of the motor). We secure the cable so that it does not come into contact with moving parts of the roller, tightening it with bodies on the axis.
- pass through The first hole inside the axis is the peasing cable (make sure the cable stays away from the moving parts of the roll and bend as smoothly as possible). The cable comes out of the edge of the shaft, on the side of the roll. To pass the cable we must first disconnect it from the rotational activation handle of the release.
- assure that the Roll is connected to the drum and lowered. We also make sure that the motor is completed (the drum cannot be rotated manually). If it is not completed, we check that the cable is working properly (the rope moves freely to the tube) and does not crack or make steep turns.
- we adjust the switch switch which corresponds to the closed position of the roll (it may be either
i.
or Ii. To this end we rotate its nearby black plastic nut until it presses both the switch to hear its click feature.
- we adjust the switch switch corresponding to the open position of the roll (the opposite switch), rotating the black plastic nut corresponding to it. The adjustment is done with successive tests, carefully to make sure that it will in no way wrap the entire length of the curtain on the axis of the roll. We always do the tests with electric function - not manually. />
< img style = "margin: 0px; padding: 0px; border: 0px; vertical-align: top;" Title = "Installation of ACM SHUTTER CENTER" SRC = "https://www.e-toolshop.gr/wp-content/uploads/2020/12/mechanical_installation-002.gif" ALT = "Installation of ACM Shutter Motor"/ >
in the next figure shows the way the roller coaster is connected to his drum motors and the use of the adapter (in case the motor has a Φ200 drum and the springs have a diameter Φ220).
< img style = "margin: 0px; padding: 0px; border: 0px; vertical-align: top;" Title = "Installation of ACM Unititan/Titan Central Motor" SRC = "https://www.e-toolshop.gr/wp-content/uploads/2020/12/mechanical_installation-003.gif" ALT = "Installation of ACM Unititan Motor Motor /Titan ”/>
i. or ii. ) corresponds to the closed position of the roller and who to the open, depends on how the motor installation is shown in the following shapes:
< img style = "margin: 0px; padding: 0px; border: 0px; vertical-align: top;" Title = "Installation of ACM Unititan/Titan Central Motor" SRC = "https://www.e-toolshop.gr/wp-content/uploads/2020/12/mechanical_installation-004.gif" ALT = "Installation of central motor ACM unititan /Titan ”/>
GUARANTEE 2 YEARS